-- ****************************************************************
-- CISCO-WAN-ATM-PARTY-MIB.my:
--
-- CISCO MSSBU ATM Point-to-Multipoint Connection Party MIB
--
-- Copyright (c) 2002 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************CISCO-WAN-ATM-PARTY-MIB DEFINITIONS::=BEGIN
IMPORTSMODULE-IDENTITY,OBJECT-TYPE,Integer32,Unsigned32FROM SNMPv2-SMI
RowStatus,TruthValue,DisplayString,TEXTUAL-CONVENTIONFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ifIndex FROM IF-MIB
ciscoMgmt FROM CISCO-SMI;ciscoWanAtmPartyMIB MODULE-IDENTITYLAST-UPDATED"200206170000Z"
ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-wanatm@cisco.com
"DESCRIPTION"A management station can use this MIB to provision,
manage or delete one or more 'parties' on an ATM
point-to-multipoint Soft PVCC(SPVC) connection.
The user must add a root endpoint to the managed system
before proceed to add one or more 'parties' to the root.
The provision and management of a 'root' endpoint is
beyond the scope of this MIB. Please refer to
CISCO-WAN-ATM-CONN-MIB.my for the provisioning and
management of a 'root' endpoint.
This MIB is based on 'ITU-T recommendation Q.2971 (10/95)
BROADBAND INTEGRATED SERVICES DIGITAL NETWORK (B-ISDN)
- DIGITAL SUBSCRIBER SIGNALLING SYSTEM No. 2 (DSS 2) -
USER-NETWORK INTERFACE LAYER 3 SPECIFICATION FOR POINT-
TO-MULTIPOINT CALL/CONNECTION CONTROL"REVISION"200206170000Z"DESCRIPTION"Initial version of the MIB"::={ ciscoMgmt 99998}
ciscoWanAtmPartyMIBNotifs
OBJECTIDENTIFIER::={ ciscoWanAtmPartyMIB 0}ciscoWanAtmPartyMIBObjects
OBJECTIDENTIFIER::={ ciscoWanAtmPartyMIB 1}cwapConfig
OBJECTIDENTIFIER::={ ciscoWanAtmPartyMIBObjects 1}ciscoWanAtmPartyMIBConform
OBJECTIDENTIFIER::={ ciscoWanAtmPartyMIB 2}-- TEXTUAL CONVENTIONSWanPartyAdminStatus ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Defines 'administrative status' of a 'party'."SYNTAXINTEGER{up(1),down(2)}
WanPartyOperStatus ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Defines 'operational status' of a 'party'."SYNTAXINTEGER{ok(1),fail(2)}WanNsapAtmAddress ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"ATM address used by the managed system. The only
address type presently supported is ATM Network Service
Access Point (NSAP) addresses (20 octets)."SYNTAXOCTETSTRING(SIZE(20))-- Party Configuration GroupcwapConfigTable OBJECT-TYPESYNTAXSEQUENCEOF CwapConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This table contains mandatory 'party' configuration
for all ATM point-to-multipoint Soft Permanent Virtual
Channel Connections (SPVC).
"::={ cwapConfig 1}cwapConfigEntry OBJECT-TYPESYNTAX CwapConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the 'cwapConfigTable'. Each entry
corresponds to one party of a point-to-multipoint
connection.
(1) To add an entry, the management
application must first provision a 'root' endpoint.
(2) While adding an entry, the variables
'cwapNSAPAddress', 'cwapVpi' and 'cwapVci' are
mandatory. The 'cwapNSAPAddress', 'csapVpi'
and 'cwapVci' are not required to be unique.
(3) The row creation will fail if the root endpoint does
not exist.
(4) The following management operations are permitted on
a row when the 'cwapRowStatus' is 'active':
a) row deletion.
b) toggling of the administrative status of a 'party'
via the 'cwapAdminStatus' object.
c) triggering a reroute via the 'cwapReroute' object.
(5) The table index 'ifIndex' refers to that of the root.
The 'ifIndex' identifies an ATM Virtual Interface
('ifType' atmVirtual(149)).
"INDEX{ifIndex, cwapRootVpi,
cwapRootVci, cwapReference}::={ cwapConfigTable 1}
CwapConfigEntry ::=SEQUENCE{
cwapRootVpi Integer32,
cwapRootVci Integer32,
cwapReference Integer32,
cwapNSAPAddress WanNsapAtmAddress,
cwapVpi Integer32,
cwapVci Integer32,
cwapAdminStatus WanPartyAdminStatus,
cwapOperStatus WanPartyOperStatus,
cwapReroute TruthValue,
cwapIdentifier Unsigned32,
cwapUploadCounter Unsigned32,
cwapRootPhysicalId DisplayString,
cwapRowStatus RowStatus}cwapRootVpi OBJECT-TYPESYNTAXInteger32(0..4095)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object identifies the Virtual Path
Identifier(VPI) of the root endpoint
this party is associated with."::={ cwapConfigEntry 1}cwapRootVci OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object identifies the Virtual
Channel Identifier (VCI) of the root
endpoint this party is associated with."::={ cwapConfigEntry 2}cwapReference OBJECT-TYPE
SYNTAXInteger32(1..65535)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer which serves to distinguish
between the multiple parties attached to a root of
a point-to-multipoint SPVC."::={ cwapConfigEntry 3}cwapNSAPAddress OBJECT-TYPESYNTAX WanNsapAtmAddress
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The ATM NSAP address of this party."::={ cwapConfigEntry 4}cwapVpi OBJECT-TYPESYNTAXInteger32(0..4095)MAX-ACCESSread-createSTATUScurrent
DESCRIPTION"The VPI value of this party."::={ cwapConfigEntry 5}cwapVci OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The VCI value of this party."::={ cwapConfigEntry 6}cwapReroute OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The management station uses this object to trigger the
re-routing of the party.
* Rerouting takes effect, when this object is set to true(1).
When set to false(2), no action is taken.
* The value 'false' will always be returned on snmp query
to this variable.
* During reroute operation, the 'cwapOperStatus' will contain
the value 'fail'. Upon successful completion of reroute,
the 'cwapOperStatus' will change to the value 'ok'. If the
reroute operation failed, the 'cwapOperStatus' will stay in
'fail'. The management station should query the
'cwapOperStatus' to decide if a reroute request is
successful or not."DEFVAL{ false }::={ cwapConfigEntry 7}cwapAdminStatus OBJECT-TYPESYNTAX WanPartyAdminStatus
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The 'administrative status' of this party.
"DEFVAL{ up }::={ cwapConfigEntry 8}cwapOperStatus OBJECT-TYPESYNTAX WanPartyOperStatus
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The 'operational status' of this party."
::={ cwapConfigEntry 9}cwapIdentifier OBJECT-TYPESYNTAXUnsigned32(0..4294967295)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An arbitrary integer which serves to
distinguish all parties on a node.
This value is assigned by the managed
system when a party is added.
The use of this variable is implementation specific."::={ cwapConfigEntry 10}cwapUploadCounter OBJECT-TYPESYNTAXUnsigned32(0..4294967295)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This counter is used by the management station to
determine if a party had been modified and requires
further action from management station.
The use of this variable is implementation specific.
This functionality is conventionally achieved by time
stamping using a time-of-day clock. However, in switches
where time-of-day clock is not available, the following
scheme is used:
The upload counter is incremented, when:
* assignment of a party to a cwapIdentifier. This
happens when a party is added and assigned this
cwapIdentifier.
* de-assignment of connection from a cwapIdentifier. This
happens when a connection is deleted.
* When there is a status change done to this party."::={ cwapConfigEntry 11}cwapRootPhysicalId OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains physical description of the
physical interface the root resides. The presentation of
this object is implementation specific."::={ cwapConfigEntry 12}cwapRowStatus OBJECT-TYPESYNTAXRowStatus
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create, modify or delete an entry
in the ciscoWanAtmPartyTable.
* A row may be created using the 'CreateAndGo' option. When
the row is successfully created, the RowStatus would be
set to 'active' by the agent.
* A row may be deleted by setting the RowStatus to 'destroy'.
"::={ cwapConfigEntry 13}ciscoWanAtmPartyMIBCompliances OBJECTIDENTIFIER::={ ciscoWanAtmPartyMIBConform 1}ciscoWanAtmPartyMIBGroups OBJECTIDENTIFIER::={ ciscoWanAtmPartyMIBConform 2}-- compliance statementsciscoWanAtmPartyMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for SNMPv2 entities which
implement one or more parties of an ATM point-to-
multi-point connection."MODULE-- this moduleMANDATORY-GROUPS{ ciscoWanAtmPartyGroup }OBJECT cwapRowStatus
SYNTAXINTEGER{
active(1), createAndGo(4), destroy(6)}-- subset of RowStatusDESCRIPTION"Only three of the six enumerated values for the
RowStatus textual convention need to be supported."::={ ciscoWanAtmPartyMIBCompliances 1}-- units of conformanceciscoWanAtmPartyGroup OBJECT-GROUPOBJECTS{
cwapNSAPAddress,
cwapVpi,
cwapVci,
cwapAdminStatus,
cwapOperStatus,
cwapReroute,
cwapIdentifier,
cwapUploadCounter,
cwapRootPhysicalId,
cwapRowStatus
}STATUScurrentDESCRIPTION"This group contains the information of a
'party' per each SPVC point-to-multipoint
connection."::={ ciscoWanAtmPartyMIBGroups 2}END